It's good to control the speed and functions of an air ventilator fan with the convenience of a remote. And you might be wondering how you could program a Fanimation remote. We're here to guide you step-by-step. We researched the answer for you!

A remote is a device used to control and navigate features of another device, like fans, through the sensor system installed on the remote's motherboard. The remote is programmed to follow a command depending on the button you press. So, to set the program of a Fanimation remote, follow these steps:

• Insert the batteries.
• Turn on the fan to connect with the electricity source
• On the remote, press and hold the "Set Key" button for five seconds
• Test the remote by pressing random buttons to see if the fan will receive the signals
• Set the fan to the desired function

It's a lot more convenient to control the function of your fan with a remote. You're away from the hassle of manually switching your fan from on to off. Just keep reading as we cover other points of interest about the topic!

About Programming a Fanimation Remote

Fanimation is a trademark of elegant fans. Their remote is meant to make the navigation of fans easier with a few taps of the buttons. See below for the detailed instructions on how to program a Fanimation remote.

See this Fanimation remote on Amazon.

 Insert the Batteries

It may seem obvious, but you will need two 3-volt CR2032 Lithium batteries. Unlike other batteries that come in cylindrical shapes, the Fanimation remote uses small, round batteries.

See this CR2032 battery set on Amazon.

The batteries will be the source of energy to power up the remote. Although the remote functions with three voltages, you still need to replace the batteries every 10 years as this is the average lifetime of the battery. This will still heavily depend though on the frequency of use.

Follow these steps to insert the batteries

• Unscrew the remote with a screwdriver.
• Place one battery in each of the two ports. The battery's smoother surface, where the word 'Lithium' is usually written below the positive sign, should face you.
• Close the battery cover.

Turn on the fan

You should turn the fan on to engage it with the remote. Make sure the fan is connected to the electrical source. Most Fanimation fans have a power button. You just need to find and press the fan's button until a light or sound indicates its activation.

Select the Fan Option

There is a button on the remote with a triangular shape and some circles. This button is in the uppermost center of the remote. Press and hold it for at least five seconds so that it will transmit the signal to the fan. Do not press with too much force, as the button may get loose.

Test the Remote

Before we introduce you to the functions of the remote, test it first by pressing buttons randomly. Also, see if the strip light on the remote has turned on. Make sure that the remote has successfully engaged with the fan. You may need to repeat the steps from inserting the battery to pressing the Set Key button.

We'll talk about troubleshooting the fan later in this article.

Prevent your remote from getting lost by using a remote holder you can mount on the wall.

See this remote holder on Amazon.

Set the Fan

Next is to enjoy your fan via the buttons on your remote. See below for the descriptions of each button and how they work.

Fan Buttons

There are three buttons on all rows, except the bottom row, which only has two. The fan buttons on top are composed of the main switch in the middle and two control buttons on both sides. The up and down buttons are for selecting the fan speed.

Light Buttons

The second row of buttons is for the light. You can turn on and off the light with the button in the middle, and control brightness with the two buttons on both sides.

Configuration Buttons

The fourth row of buttons is designated for function settings.

Press the left button and the light will blink twice, indicating that the setup is complete. The fan will turn off and the lights will switch on and off randomly. Press any button to cancel this function.

The middle button is for natural breezes. Press it to set the fan into breeze mode.

Press the right button. The light should blink once to indicate that you have completed the setup. The fan and light will turn off after a minute. You may press any button to cancel this function.

Reverse Buttons

The reverse buttons are on the bottom row. The buttons have sun symbols for summer mode and snowflakes for winter mode.

The summer mode button on the right will make the fan spin counterclockwise. The fan will release cool air downwards. On the left button, the winter mode will release warm air downwards. The fan will then spin clockwise.

How to Troubleshoot Fanimation Ceiling Light and Fan

If you've made all the effort to set the remote but the fan does not react, then maybe the fan is defective. See below the things you should look for when troubleshooting the fan.

Electrical Source

The first thing to check is the electrical source. See if the socket is properly plugged in and the wires are in good condition. You may need to consult an electrician to fix the wires, specifically if the household wires are at fault.

The Fan Stops

There might be a problem with the fan motor. Take note that you should let the fan rest when not in use. Turn off the fan for 1–4 hours so that it recovers from being overused.

Light Won't Turn On

The fan's components may naturally lose energy over time. Check if the bulbs are tight. You can ask the manufacturer if they have an available bulb for replacement depending on your model.

No Air

If the fan is spinning but there's no air coming from it, then the motor might have reached its limit. You need a motor replacement, or even a replacement of the fan itself.

However, you can just check if the blades are dusty. It might be the reason why air is not flowing downwards. You can use a ceiling fan broom to reach the blades and wipe the dust off.

See this ceiling fan broom on Amazon.

Other Types of Fanimation Remote

There are other types of Fanimation remote for the convenience of use. See below for these common types and how to activate them.

Wall Remotes

These are installed on walls with the wires connecting the Fanimation lights and fan. These are easier to navigate due to fewer buttons to press. Also, wall remotes don't require batteries. They can run as long as there's an electrical source.

You need a technician to mount the remote on the wall. However, you can simply turn it on by sliding the switch and pressing the fan level.

Bluetooth

This new technology allows you to control the fan and lights with your phone. You just need Bluetooth on your mobile device connected with the physical remote. To set up this option, follow these steps.

1. Install the FanSync application on your phone. Most modern phones are compatible with this function.
2. Connect your phone to the remote via Bluetooth.
3. See the pop-up message that will appear on your phone. The remote functions should appear on screen, and you'll be able to control the Fanimation device with them.

Not all fans have this control option. You need to check the compatibility of your phone with the version of the remote you'll use. You can ask the manufacturer about this matter.

How Long Does a Fanimation Ceiling Fan Last?

Fanimation ceiling fans can last for up to 10 years or longer. It's best not to overuse the fan to prolong its lifespan. Is the

Is Fanimation Remote Compatible With Other Devices

Most Fanimation remotes will not work for other devices since they are programmed for Fanimation devices only.

Conclusion

Throughout this article, we've learned how to program a Fanimation remote. We've discussed its different functions. You've learned how to troubleshoot the Fanimation light and fan, like checking the electrical source and fan motor.

We also learned about other types of Fanimation remotes. Remind yourself that the fan needs a rest to prolong its lifespan.

We know you want to learn more. Visit these articles:

How To Fix A Ceiling Fan Light

What Is A Good Airflow For A Ceiling Fan?