As a homeowner, you may want to install a storm door in your home without brick molding but wondering how to go about it. Luckily, we have done some research for you, and here is what we found.
The following is the step-by-step guide for installing a storm door without brick molding:
- Determine the size of the door frame
- Get the frame ready for mounting
- Cover the frame with the storm door
- Mark the position of the hinge
- Align the door faceplate with the latch
- Install a rubber seal around the door
A storm door can be easily installed. All you have to do is follow the steps carefully. Keep reading to get detailed information on installing a storm door without brick molding.
Installing A Storm Door Without Brick Molding [Step By Step Guide]
Before you install a storm door, you will need tools like a power drill, drill bits, hammer, screwdriver, 1 and 3-inch galvanized wood screws, rubber weather stripping, carpentry stapler, and furring strip.
When the tools are ready, you can now proceed with the following steps:
Step 1: Determine The Size Of The Door Frame
Measure where the storm door will be installed. Take a measurement all the way down to the ground from the top of the door frame. The next thing to do is measure the width of the door frame.
Step 2: Get The Frame Ready For Mounting
To ensure a tight fit, storm doors are typically manufactured to be just a little bit smaller in width than the actual opening. Find the distance between the trim's interior borders on the external door frame.
A furring strip on the hinge side of the door frame can make up the difference in width between the storm door and the door frame, ensuring a tight fit. Using nails, hammer the furring strip into position.
Step 3: Cover The Door Frame With The Storm Door
This step is very crucial. Storm doors should be installed so that the exterior faces outward and the entire door opening is covered. The storm door's hinges are reversible, so they should go on either the left or right side.
Step 4: Mark The Position Of The Hinge
Mark the wall where the screw holes in the hinges are, and then remove the storm door. After that, start drilling through the markings and into the door frame.
After the storm door has been reinstalled, partially screw a galvanized wood screw measuring 3 inches into each hole.
Once all of the screws from both hinges have been partially fixed, you must go back and fully tighten all the screws. You can check the door's alignment by opening and closing it.
If required, you can make some changes by shifting the screws that hold the hinges in place.
Step 5: Align The Door Faceplate With The Latch
To ensure that the door faceplate is flush with the frame when the latch is engaged, install it exactly where the latch will make contact. Take note of where the screw holes are on the face plate.
Simply take off the cover and drill out the corresponding hole. After replacing the faceplate, secure it with the galvanized wood screws that are 1-inch in measurement.
Step 6: Install A Rubber Seal Around The Door
Install rubber weather stripping along the perimeter of the storm door, either externally or inside, keeping it in place with a carpenter's stapler.
Click here to see this power drill set on Amazon.
Click here to see this drill bit set on Amazon.
Click here to view this screwdriver on Amazon.
Click here to see this stapler gun on Amazon.
How Long Does It Take To Install A Storm Door?
The amount of time needed to install a storm door depends on both the task involved and the installer's level of expertise.
It will take a homeowner at least four hours to install a storm door, but it takes a professional about thirty minutes to get the job done.
How Much Does It Cost To Have A Storm Door Installed?
A storm door installation might cost anywhere from $300 to $750. This price may vary based on different factors.
The average price that a homeowner would spend to install a mid-view door, including a few optional upgrades, is around $450.
A basic storm door, which does not include additional features or installation, may be purchased for as low as $230.
It is possible that the installation of a fully glazed double storm door that has basic security features would cost up to $1,500.
Should You Put A Storm Door On Your Front Door?
When deciding whether or not a storm door is the most suitable choice for your home, a few considerations need to be given priority. Consider the climate at your location.
Also, if your primary door is brand new, well insulated, and energy efficient, you may not require or even want to have a storm door installed.
An outside storm door might not be the best option for those living in warm areas. However, if your front door is easily affected by elements, you need to install a storm door.
The United States Department of Energy recommends that you should not install a storm door at your front entry if it is exposed to more than two or three hours of direct sunlight daily.
As a result, the storm door might potentially cause damage to your entry door by preventing heat from escaping. If you must install a storm door, your best bet is to search for one that combines ventilation with low-emissive glass.
You may not need a storm door if the primary goal of decreasing your energy expenditures is met with a contemporary, well-sealed front door and if you already have one.
You may not even need a storm door if the major entry to your home is protected from the weather by a large overhang or a covered porch.
Which Way Should Storm Door Open?
Storm doors are an essential component of your home. Due to their importance, the swing direction of storm doors should be gotten correctly.
Storm doors can only be opened in one direction, which is outward since they are linked to the exterior of the primary entrance. The direction of the swing is often dictated by how the outer door swings, as these two directions, are almost always the same.
Should Storm Door Handle Be On Same Side As Door?
The simple answer is YES. It is common practice to line up the door handle of the main entry and the storm door so that opening either door may be done from the same side of the door. That is the method that is always followed.
If the jamb depth measurements aren't deep enough for a suitable installation, there is a chance that the storm door handle will collide with the door lever of the entry door.
Does Storm Door Keep Cold Out?
Yes, it does. During winter, having a storm door may help keep your home warmer; in the summer, it can help keep your home cooler.
During the cooler months, they act as insulation for your home, and during the warmer months, they prevent hot air from entering. They help in regulating the temperature within a home that has enough insulation.
They have the added benefit of preventing water damage to your front door, which can be caused by rain.
It is possible that installing a storm door on the primary entrance of your property will assist in preventing rain and snow from entering.
To Wrap Up
You can install a storm door without brick molding on your own. All you need to do is determine the size of the door frame, get the frame ready for mounting, cover the frame with the storm door, mark the position of the hinge, and align the door faceplate with the latch.
Don't forget to install a rubber seal around the door. You can hire a professional if you find it difficult to do the task alone.
If you enjoyed reading this post, here are similar articles you may like:
How To Insulate Windows From The Outside [Step By Step Guide]
How To Insulate Fireplace Not In Use
How To Insulate A Wooden Front Door - 6 Methods For Improvement