Was there a sudden power outage in your area, and when the electricity came back, your Bryant air conditioner split unit won't turn on or started acting strangely? Before you call your HVAC service provider, why don't you try resetting it first? Don't know how to do it? Here are the simple steps as advised by experts.
Since most Bryant air conditioning units do not have a reset button, you just need to turn off the circuit breaker and wait for a few minutes before turning it back on to reset it.
Keep on reading so we can tell you more about resetting your Bryant air conditioner. We'll also share with you how long this usually takes. This article will also tackle why your AC isn't working properly and how to fix these issues. Lastly, we'll talk about the thermostat and how to know if it has already gone bad. Let's get the troubleshooting started!
How do I reset my Bryant air conditioner?
Resetting your air conditioning unit is sometimes necessary especially after there has been a power outage. The sudden influx of electrical voltage once the power comes back may have prompted your circuit breaker to perform the necessary protective measure of shutting down your AC to mitigate the risk of fire and possible explosions.
Aside from a tripped breaker, there are times when the little kids might have had too much fun with the remote, which could lead to errors on the digital panel, and you'll find that your AC is not working properly anymore.
These are just some instances when your air conditioning unit may benefit from doing the good old-fashioned reset to get it back to work properly.
And the best thing about it is that it is so easy to do. You just press the reset button, and you're done! This will usually solve the issue without any need to call a technician.
However, if you have a Bryant air conditioner, this might be a little confusing for you because you can't find the reset button. You may have searched the unit for that red button and double-checked the manual for its location, but still, you didn't find any. Unlike other air conditioning units, most Bryant ACs don't come with a reset button.
But don't worry, there's a way for you to reset your unit. Here's how.
1. Look for your AC's dedicated circuit breaker and turn it off. 2. Wait for a few minutes. 3. Turn the breaker back on.
That's it! It's still an easy process, right? Sometimes this is all it takes to get your AC to work properly again. It just requires you to try simple things such as resetting your AC to give it time to reboot, and it'll be okay once again.
How long does it take for an AC unit to reset?
How long should you wait before you turn the breaker back on? How long are a few minutes anyway before you can use your air conditioner again?
Experts recommend that you shut off your AC for 30 minutes. This should give it adequate time to reboot its system and fix internal issues.
It is also not advisable to reset your air conditioner again and again. If it still doesn't work properly after the reset, it's best to call your trusted HVAC service provider to check what could be wrong with your appliance.
Why is my Bryant AC not working?
There are various reasons why your Bryant AC is not working properly. It may involve any of these parts:
- air filter,
- condenser coils,
- compressor,
- temperature control thermostat,
- main control board,
- temperature control board,
- thermistor,
- or run capacitor.
According to the manufacturers, the first thing that you need to do is to check if your thermostat is at the "cool" position. Then make sure that the outdoor condensing unit is also on. Check its circuit breaker box outside as well as its disconnect switch to be certain that they are running.
Once you've confirmed that these parts are activated but your Bryant air conditioner isn't cooling, try these troubleshooting tips to put it back in order.
Clogged air filter
When this happens, the air inside the AC won't be able to flow properly, thus affecting the unit's capacity to cool the air. This can also cause the evaporator coils to freeze.
Clean the filter by removing the debris that has accumulated inside, or it might be time to have the filter replaced.
Dirty condenser coils
These coils are essential for dissolving the heat from the refrigerant. But if they are dirty, they won't be able to do their job properly. It would be hard for your air conditioning unit to maintain your desired temperature.
The entire unit, especially the compressor, would need to work harder to make the air cooler. You need to have them cleaned so that they can function effectively.
Faulty thermistor
This is a sensor that detects air temperature. It is connected to the AC's control board. If it is defective, its value won't change even if there's a temperature change. You will need to use a multimeter to check for the thermistor's continuity. If it doesn't have continuity, then you need to have your thermistor replaced.
Burned out run capacitor
This component is essential in keeping the compressor going. If it is already burned out, you need to replace it. A multimeter test will help you determine its condition.
Faulty compressor
If you've checked the compressor capacitor and overload protector and don't see anything wrong with these parts, then you might have a defective compressor. This needs to be replaced by a qualified technician so you can have your air conditioner back in great condition.
Failing main control board and temperature control board
If you have a malfunctioning main control board or temperature control board, your air conditioning unit might not work at all. This is because these parts are responsible for regulating the electrical energy that your AC needs to work.
If your unit has been diagnosed with a defective main control board or temperature control board, you would need to have the corresponding part replaced to have your AC working again.
It is important to have your Bryant air conditioning unit checked by a licensed technician because these issues are often misdiagnosed. Only a professional would be able to rule out other defects before concluding that the problem is, indeed, with the main control board or its temperature control board.
How do you know a thermostat is bad?
Another possible reason why your Bryant air conditioner is not working properly is a defective thermostat. The thermostat powers the AC's fan and compressor to maintain your desired temperature.
- It starts registering incorrect temperature readings.
- There are fluctuating temperatures in the room, and the temperature could change without warning.
- There are many instances of short cycles or earlier shutoffs than the designated time for the full cooling cycle.
- The thermostat remains unresponsive even if you've already adjusted the settings several times.
- Your AC keeps turning on and off.
- You notice a sudden change in your electric bill. The inefficient thermostat is usually the culprit!
You can use a multimeter to determine if your thermostat is not working properly. If the thermostat is set to the "cooling" position, but the multimeter doesn't show continuity, you know that you have a defective part right there. The only way to fix this is to replace it with a new one.
Final Thoughts
Resetting your Bryant air conditioner split unit is so easy, even without the reset button. Just turn its circuit breaker off and turn it back on after 30 minutes. Sometimes it takes something as simple as resetting your AC to get it back to work properly, and you'll realize that you don't have to call your HVAC service provider right away when you have a tripped breaker or encounter error signals on the control panel.
For more related reading about your air conditioning unit, you may visit the following posts: